Home >

Knowledge

25Sep 2024

Frequently checked parts and treatment methods when conveyor belt deviates

(1) Check the misalignment between the horizontal center line of the roller and the longitudinal center line of the belt conveyor. If the misalignment value exceeds 3mm, it should be adjusted using th
23Sep 2024

Specific precautions for daily use of conveyor belts

1. Whether in use or not, the conveyor belt should keep the entire table clean, avoid direct sunlight or rain and snow, prevent contact with materials such as acid, alkali, oil, organic solvents, and
20Sep 2024

Precautions for using pu timing belts

1. Unused pu timing belts should be packed and placed indoors. 2. If the pu timing belt is installed on the machine but has not been used, it can be wrapped with a wrapping film. 3. If the pu timing b
18Sep 2024

PVC conveyor belt bending problem

1. The thickness of the two sides of the PVC conveyor belt is different. The thick side is easier to stretch than the thin side, which will cause the length of the two sides to be inconsistent, causin
16Sep 2024

What are the common processing methods for PVC conveyor belts?

1. Adding skirts Most ordinary conveyor belts are flat belts. When conveying bulk materials or granular materials, it is easy to scatter or leak materials. At this time, seamless skirts can be added o
16Sep 2024

What are the maintenance methods for rubber conveyor belts?

1. During storage, the temperature in the warehouse should be kept between -15℃ and +40℃, and the relative humidity should be kept between 50-80%. 2. During transportation and storage, the rubber conv
13Sep 2024

Reasons for tearing of PVC conveyor belts

1. Reasons for longitudinal tearing of PVC conveyor belts: 1. Vibration and impact cause fasteners to loosen and fall off, causing lining plates, guide plates, etc. to fall. 2. Foreign objects are mix
11Sep 2024

What should be noted when using the transverse joints of conveyor belts?

1. The core of the whole flame retardant belt shall not have transverse joints; 2. The transverse joints of the core of the layered flame retardant belt shall not be greater than 60° and not less
06Sep 2024

What are the factors that affect the ductility of conveyor belts?

1. The tension of the conveyor belt is too tight The indicator of whether the tension is adjusted in place is that the conveyor belt can operate normally after installation without slipping or deviati
04Sep 2024

General detection method for PVC conveyor belts

Conveyor belt breakage can be detected by adding a breakage detection device, testing the results in a relatively short time, issuing an alarm and shutting down. Strengthen the management of mechanica
02Sep 2024

How to adjust the tension of the patterned conveyor belt?

1. Spiral tensioning device Features: The tensioning stroke is short (generally 500mm-1000mm), and the conveyor belt is tensioned by connecting the tensioning screw to the tensioning roller, and the s
30Aug 2024

Four major hazards caused by PVC conveyor belt damage

(1) The conveyor belt becomes very thin and inconvenient to overlap. The surface damage of the conveyor belt makes its thickness thinner. When overlapping the two ends, the thickness of the joints is

First 21 22 23 24 25 26 27 Last 24/58

Knowledge

Frequently checked parts and treatment methods when conveyor belt deviates

Specific precautions for daily use of conveyor belts

Precautions for using pu timing belts

PVC conveyor belt bending problem

What are the common processing methods for PVC conveyor belts?

What are the maintenance methods for rubber conveyor belts?

Reasons for tearing of PVC conveyor belts

What should be noted when using the transverse joints of conveyor belts?

What are the factors that affect the ductility of conveyor belts?

​​General detection method for PVC conveyor belts

How to adjust the tension of the patterned conveyor belt?

Four major hazards caused by PVC conveyor belt damage

General detection method for PVC conveyor belts