Home >

Knowledge

22Dec 2025

What are the common forms of damage to PVC conveyor belts?

1. Edge wear: Caused by friction between the belt and the frame due to misalignment, resulting in thinning of the edges and exposed fibers. 2. Longitudinal tear: Caused by scratches from sharp objects
19Dec 2025

How to determine the temperature resistance of a PU conveyor belt?

1. Clarify Temperature Resistance Standards Regular PU conveyor belts: The upper limit of temperature resistance is usually 80℃, but in actual use, it is recommended to allow a 10℃ margin, meaning the
17Dec 2025

Does a PVC timing belt need adjustment after replacement?

1. No-load test: Start the equipment and observe whether the operation is smooth, checking for any abnormal noise or vibration. 2. Tension adjustment: Press the middle of the belt with your thumb; the
15Dec 2025

What are the steps for replacing a PVC timing belt?

1. Preparation Ensure the equipment is powered off. Prepare a new timing belt (matching the old belt's specifications) and tools such as a wrench and screwdriver. 2. Removing the Old Timing Belt L
12Dec 2025

How to determine if a PVC timing belt needs replacement?

Visual Inspection 1. Surface Wear: If obvious grooves, cracks, or edge tears appear, replace immediately. 2. Deformation/Hardening: If it does not spring back after being pressed or the surface is whi
10Dec 2025

How to maintain a PVC timing belt after cleaning to extend its lifespan?

Post-cleaning maintenance methods: 1. Environmental control: After cleaning, store in a dry, ventilated place, avoiding direct sunlight or contact with acidic, alkaline, or oily substances. The recomm
08Dec 2025

What precautions should be taken when cleaning PVC timing belts?

Cleaning Method Selection 1. Light Stains: Wipe surface dust with a damp cloth. 2. Heavy Stains: Spray with a special cleaner (such as neutral detergent), gently brush with a soft brush, and then wipe
05Dec 2025

How to Properly Clean a PVC Timing Belt?

Steps for Cleaning a PVC Timing Belt 1. Daily Cleaning: Gently wipe surface dust with a damp cloth. Avoid using strong acid or alkali cleaners. 2. Stubborn Stains: Spray with a special cleaner (such a
03Dec 2025

What are some common mistakes when installing PVC timing belts?

1. Misaligned pulleys Symptoms: The axes of the two pulleys are not parallel or the angle is off, causing the timing belt to run off-center and wear on one side. Solution: Use a laser alignment instru
01Dec 2025

How to Properly Install and Maintain a PVC Synchronous Belt?

Installation Steps 1. Preparation: Disconnect the power supply and remove protective equipment. Loosen the motor connection bolts and shorten the center distance between the pulleys. 2. Install the Sy
30Nov 2025

How does the pattern of a PVC conveyor belt affect the load?

1. Diamond Pattern: The raised height is typically 2-5mm, increasing friction by increasing the contact area, suitable for medium to high loads (such as food processing and logistics sorting). However
28Nov 2025

How to test after replacing a PVC conveyor belt?

1. No-load test run: Start the equipment and run it without load for 5-10 minutes. Observe whether the belt is misaligned or makes any abnormal noises (such as friction or slippage). Check whether the

First 7 8 9 10 11 12 13 Last 10/60

Knowledge

What are the common forms of damage to PVC conveyor belts?

How to determine the temperature resistance of a PU conveyor belt?

Does a PVC timing belt need adjustment after replacement?

What are the steps for replacing a PVC timing belt?

How to determine if a PVC timing belt needs replacement?

How to maintain a PVC timing belt after cleaning to extend its lifespan?

What precautions should be taken when cleaning PVC timing belts?

How to Properly Clean a PVC Timing Belt?

What are some common mistakes when installing PVC timing belts?

How to Properly Install and Maintain a PVC Synchronous Belt?

How does the pattern of a PVC conveyor belt affect the load?

How to test after replacing a PVC conveyor belt?